{"id":191,"date":"2023-03-27T10:57:22","date_gmt":"2023-03-27T14:57:22","guid":{"rendered":"https:\/\/pressbooks.bccampus.ca\/level2layout\/?post_type=chapter&p=191"},"modified":"2023-03-30T12:38:10","modified_gmt":"2023-03-30T16:38:10","slug":"off-center-square-to-round","status":"publish","type":"chapter","link":"https:\/\/pressbooks.bccampus.ca\/level2layout\/chapter\/off-center-square-to-round\/","title":{"raw":"Off Center Square to Round","rendered":"Off Center Square to Round"},"content":{"raw":"
The only difference with this fitting is a few more element line lengths than an on-centre, the process is exactly the same.<\/div>\r\n
    \r\n \t
  1. Draw a full [pb_glossary id=\"532\"]plan view[\/pb_glossary]<\/strong> complete with all [pb_glossary id=\"527\"]element lines[\/pb_glossary] <\/strong>and labeling. Choose a line of symmetry to place the seam so you only need to make 1 pattern. Label one half of the plan view, the round end with numbers and the square end with letters.\"\"<\/li>\r\n \t
  2. Create a [pb_glossary id=\"540\"]TLD[\/pb_glossary] <\/strong>and label it\r\n\"\"<\/li>\r\n \t
  3. Draw a baseline equal to line A-B.\r\n\"\"<\/li>\r\n \t
  4. Pick up the [pb_glossary id=\"539\"]true length[\/pb_glossary]<\/strong> of line A-4 and swing it from point A.\"\"<\/li>\r\n \t
  5. Next, pick up true length of line B-4 and swing it from point B. Where it crosses the first arc, becomes point \"\"<\/li>\r\n \t
  6. Pick up a step-off from the plan view and swing it from point 4. Unlike an on-centre square to round, this fitting needs to be developed one side at a time. Complete one side, then go back to finish the other side.\"\"<\/strong><\/li>\r\n \t
  7. Pick up the true length of line A-3 and swing it from point A.\"\"<\/li>\r\n \t
  8. Pick a step-off and swing it from point 3.\"\"<\/li>\r\n \t
  9. Pick up the true length of line A-2 and swing it from point A.\"\"<\/li>\r\n \t
  10. Pick up a step-off and swing it from 2.\r\n\"\"<\/li>\r\n \t
  11. Pick up the true length of line A-1 and swing it from point A.\"\"<\/li>\r\n \t
  12. Pick up the true length of line D-1 and swing it from 1.\"\"<\/li>\r\n \t
  13. Pick up line A-D from the plan view (remember that letter to letter is true length) and swing it from point A. Remember that point D should be 90<\/strong>\u00b0. If it not, go back and check your work.\r\n\"\"<\/strong><\/li>\r\n \t
  14. Now, go back to point 4 and work the pattern to the other side, completing it at point C. Notice in this example, line C-7 has no length in the plan view, it is a dot. The true length is the [pb_glossary id=\"522\"]vertical[\/pb_glossary]<\/strong> height. Zero plan length put 90 deg to the vertical height, will have no change to the vertical height.\"\"<\/li>\r\n \t
  15. Draw in the all the element lines and outside edges, using a flexible curve for the round end.\"\"<\/li>\r\n<\/ol>","rendered":"
    The only difference with this fitting is a few more element line lengths than an on-centre, the process is exactly the same.<\/div>\n
      \n
    1. Draw a full plan view<\/strong> complete with all element lines <\/strong>and labeling. Choose a line of symmetry to place the seam so you only need to make 1 pattern. Label one half of the plan view, the round end with numbers and the square end with letters.\"\"<\/li>\n
    2. Create a TLD <\/strong>and label it
      \n\"\"<\/li>\n
    3. Draw a baseline equal to line A-B.
      \n\"\"<\/li>\n
    4. Pick up the true length<\/strong> of line A-4 and swing it from point A.\"\"<\/li>\n
    5. Next, pick up true length of line B-4 and swing it from point B. Where it crosses the first arc, becomes point \"\"<\/li>\n
    6. Pick up a step-off from the plan view and swing it from point 4. Unlike an on-centre square to round, this fitting needs to be developed one side at a time. Complete one side, then go back to finish the other side.\"\"<\/strong><\/li>\n
    7. Pick up the true length of line A-3 and swing it from point A.\"\"<\/li>\n
    8. Pick a step-off and swing it from point 3.\"\"<\/li>\n
    9. Pick up the true length of line A-2 and swing it from point A.\"\"<\/li>\n
    10. Pick up a step-off and swing it from 2.
      \n\"\"<\/li>\n
    11. Pick up the true length of line A-1 and swing it from point A.\"\"<\/li>\n
    12. Pick up the true length of line D-1 and swing it from 1.\"\"<\/li>\n
    13. Pick up line A-D from the plan view (remember that letter to letter is true length) and swing it from point A. Remember that point D should be 90<\/strong>\u00b0. If it not, go back and check your work.
      \n\"\"<\/strong><\/li>\n
    14. Now, go back to point 4 and work the pattern to the other side, completing it at point C. Notice in this example, line C-7 has no length in the plan view, it is a dot. The true length is the vertical<\/strong> height. Zero plan length put 90 deg to the vertical height, will have no change to the vertical height.\"\"<\/li>\n
    15. Draw in the all the element lines and outside edges, using a flexible curve for the round end.\"\"<\/li>\n<\/ol>\n
      definition<\/span>