{"id":238,"date":"2020-11-18T08:47:25","date_gmt":"2020-11-18T13:47:25","guid":{"rendered":"https:\/\/pressbooks.bccampus.ca\/pressbookbccampussmlt1\/chapter\/off-center-90-deg-tee\/"},"modified":"2023-03-17T13:08:08","modified_gmt":"2023-03-17T17:08:08","slug":"off-center-90-deg-tee","status":"publish","type":"chapter","link":"https:\/\/pressbooks.bccampus.ca\/pressbookbccampussmlt1\/chapter\/off-center-90-deg-tee\/","title":{"raw":"Off Centre 90 Degree Tee","rendered":"Off Centre 90 Degree Tee"},"content":{"raw":"
    \r\n \t
  1. Draw a full front [pb_glossary id=\"528\"]elevation view[\/pb_glossary]<\/strong> and end elevation view.\"\"<\/strong><\/li>\r\n \t
  2. Draw [pb_glossary id=\"533\"]profiles[\/pb_glossary]<\/strong> on the tee in both views and divide into 6 equal parts (see Divide a Circle Into 12 Equal Parts<\/a>). Include all labeling. Remember that the labeling will flip with the view.\"\"<\/strong><\/li>\r\n \t
  3. Draw in the [pb_glossary id=\"527\"]element lines[\/pb_glossary]<\/strong> from the profile divisions.\"\"<\/li>\r\n \t
  4. Where the element lines hit the pipe in the end view, project them [pb_glossary id=\"508\"]horizontally[\/pb_glossary]<\/strong> into the front view.\"\"<\/li>\r\n \t
  5. Following the labeling, draw in the [pb_glossary id=\"530\"]miter[\/pb_glossary] line<\/strong> in the front view.\"\"<\/li>\r\n \t
  6. Draw the tee [pb_glossary id=\"534\"]stretch-out[\/pb_glossary]<\/strong> and divide into 12 equal parts (see Divide a Line Using a Ruler on an Angle<\/a>). Label the stretch-out to match the elevation view.\"\"<\/strong><\/li>\r\n \t
  7. Transfer\/project the corresponding points from the front elevation view\u00a0to the\u00a0stretch-out.\"\"<\/strong><\/li>\r\n \t
  8. Circle the points and use a flexible curve to complete the [pb_glossary id=\"531\"]pattern[\/pb_glossary]<\/strong>.\"\"<\/strong><\/li>\r\n<\/ol>\r\nhttps:\/\/www.youtube.com\/watch?v=MK_wQVvz2mw&list=PL0YcC46LnT8di2DsnBZrMgeEtso_LWIHL&index=6\r\n\r\n ","rendered":"
      \n
    1. Draw a full front elevation view<\/a><\/strong> and end elevation view.\"\"<\/strong><\/li>\n
    2. Draw profiles<\/a><\/strong> on the tee in both views and divide into 6 equal parts (see Divide a Circle Into 12 Equal Parts<\/a>). Include all labeling. Remember that the labeling will flip with the view.\"\"<\/strong><\/li>\n
    3. Draw in the element lines<\/a><\/strong> from the profile divisions.\"\"<\/li>\n
    4. Where the element lines hit the pipe in the end view, project them horizontally<\/a><\/strong> into the front view.\"\"<\/li>\n
    5. Following the labeling, draw in the miter<\/a> line<\/strong> in the front view.\"\"<\/li>\n
    6. Draw the tee stretch-out<\/a><\/strong> and divide into 12 equal parts (see Divide a Line Using a Ruler on an Angle<\/a>). Label the stretch-out to match the elevation view.\"\"<\/strong><\/li>\n
    7. Transfer\/project the corresponding points from the front elevation view\u00a0to the\u00a0stretch-out.\"\"<\/strong><\/li>\n
    8. Circle the points and use a flexible curve to complete the pattern<\/a><\/strong>.\"\"<\/strong><\/li>\n<\/ol>\n