{"id":378,"date":"2021-07-24T00:45:06","date_gmt":"2021-07-24T04:45:06","guid":{"rendered":"https:\/\/pressbooks.bccampus.ca\/pressbookbccampussmlt1\/chapter\/cone-on-a-pitch-miter-print\/"},"modified":"2023-03-17T13:19:01","modified_gmt":"2023-03-17T17:19:01","slug":"cone-on-a-pitch-miter-print","status":"publish","type":"chapter","link":"https:\/\/pressbooks.bccampus.ca\/pressbookbccampussmlt1\/chapter\/cone-on-a-pitch-miter-print\/","title":{"raw":"Cone on a Pitch\/Miter","rendered":"Cone on a Pitch\/Miter"},"content":{"raw":"
    \r\n \t
  1. Draw an [pb_glossary id=\"528\"]elevation view[\/pb_glossary]<\/strong>, including the [pb_glossary id=\"535\"]apex[\/pb_glossary] point<\/strong>.\"\"<\/strong><\/li>\r\n \t
  2. [pb_glossary id=\"533\"]Profile[\/pb_glossary]<\/strong> the base of the elevation view and divide it into six equal parts.\"\"<\/li>\r\n \t
  3. Label the profile from 1 to 7 and project the divisions vertically into the base of the cone.\"\"<\/li>\r\n \t
  4. Project the [pb_glossary id=\"527\"]element lines[\/pb_glossary]<\/strong> from the base to the apex of the cone.\"\"<\/li>\r\n \t
  5. Draw in the [pb_glossary id=\"530\"]miter[\/pb_glossary] line<\/strong>.\r\n\"\"<\/strong><\/li>\r\n \t
  6. Where the element lines cross the miter line, project them horizontally to the outside edge. This now creates seven different slant heights.\r\n\"\"\r\n<\/b><\/li>\r\n \t
  7. Locate a\u00a0radius point where you want to develop the pattern.\"\"<\/li>\r\n \t
  8. With your compass, take the large\u00a0[pb_glossary id=\"536\"]slant height[\/pb_glossary]<\/strong> and swing an arc.\"\"<\/li>\r\n \t
  9. Set your compass to all of the remaining\u00a0slant heights\u00a0and swing them from the\u00a0radius point.\"\"<\/strong><\/li>\r\n \t
  10. Establish a starting point for the pattern and draw a line back to the\u00a0radius point.\"\"<\/strong><\/li>\r\n \t
  11. Set your compass to a step-off. From your starting point, swing it 12 times along the [pb_glossary id=\"537\"]stretch-out arc[\/pb_glossary]<\/strong>\u00a0and label each point to match the\u00a0elevation view.\u00a0Start your numbering where you want the seam, commonly put on the short side of the cone.\"\"<\/strong><\/li>\r\n \t
  12. Connect the all of the points back to the\u00a0radius point.\"\"<\/strong><\/li>\r\n \t
  13. Following your numbering, circle each intersection point.\u00a0This will create the pattern of over 1, down 1.\"\"<\/strong><\/li>\r\n \t
  14. Use a flexible curve to connect the points and create the pattern.\"\"<\/li>\r\n<\/ol>\r\nhttps:\/\/www.youtube.com\/watch?v=Bngtr61GppA&list=PL0YcC46LnT8di2DsnBZrMgeEtso_LWIHL&index=11","rendered":"
      \n
    1. Draw an elevation view<\/a><\/strong>, including the apex<\/a> point<\/strong>.\"\"<\/strong><\/li>\n
    2. Profile<\/a><\/strong> the base of the elevation view and divide it into six equal parts.\"\"<\/li>\n
    3. Label the profile from 1 to 7 and project the divisions vertically into the base of the cone.\"\"<\/li>\n
    4. Project the element lines<\/a><\/strong> from the base to the apex of the cone.\"\"<\/li>\n
    5. Draw in the miter<\/a> line<\/strong>.
      \n\"\"<\/strong><\/li>\n
    6. Where the element lines cross the miter line, project them horizontally to the outside edge. This now creates seven different slant heights.
      \n\"\"
      \n<\/b><\/li>\n
    7. Locate a\u00a0radius point where you want to develop the pattern.\"\"<\/li>\n
    8. With your compass, take the large\u00a0slant height<\/a><\/strong> and swing an arc.\"\"<\/li>\n
    9. Set your compass to all of the remaining\u00a0slant heights\u00a0and swing them from the\u00a0radius point.\"\"<\/strong><\/li>\n
    10. Establish a starting point for the pattern and draw a line back to the\u00a0radius point.\"\"<\/strong><\/li>\n
    11. Set your compass to a step-off. From your starting point, swing it 12 times along the stretch-out arc<\/a><\/strong>\u00a0and label each point to match the\u00a0elevation view.\u00a0Start your numbering where you want the seam, commonly put on the short side of the cone.\"\"<\/strong><\/li>\n
    12. Connect the all of the points back to the\u00a0radius point.\"\"<\/strong><\/li>\n
    13. Following your numbering, circle each intersection point.\u00a0This will create the pattern of over 1, down 1.\"\"<\/strong><\/li>\n
    14. Use a flexible curve to connect the points and create the pattern.\"\"<\/li>\n<\/ol>\n