{"id":486,"date":"2021-07-24T01:03:40","date_gmt":"2021-07-24T05:03:40","guid":{"rendered":"https:\/\/pressbooks.bccampus.ca\/pressbookbccampussmlt1\/chapter\/off-centre-round-taper-print\/"},"modified":"2023-03-17T13:21:28","modified_gmt":"2023-03-17T17:21:28","slug":"off-centre-round-taper-print","status":"publish","type":"chapter","link":"https:\/\/pressbooks.bccampus.ca\/pressbookbccampussmlt1\/chapter\/off-centre-round-taper-print\/","title":{"raw":"Off-Centre Round Taper","rendered":"Off-Centre Round Taper"},"content":{"raw":"
    \r\n \t
  1. Draw a full [pb_glossary id=\"532\"]plan view[\/pb_glossary]<\/strong> complete with all [pb_glossary id=\"527\"]element lines[\/pb_glossary] <\/strong>and labeling. Label one half of the plan view, go from large end to small end, zigzagging back and forth with the numbering 1-14. Remember, every round to round will be on centre one way, but it is always worth drawing the whole thing.\"\"<\/strong><\/li>\r\n \t
  2. Create a\u00a0[pb_glossary id=\"540\"]TLD[\/pb_glossary]<\/strong>\u00a0and label all the\u00a0element lines.\"\"<\/strong><\/li>\r\n \t
  3. Draw a vertical line equal to the [pb_glossary id=\"539\"]true length[\/pb_glossary]<\/strong> of line 13-14.\"\"<\/li>\r\n \t
  4. From the\u00a0TLD, pick up the true length of line 13-12 and swing it from point 13 back towards point 14. Remember to work both sides at the same time.\"\"<\/strong><\/li>\r\n \t
  5. Next, pick up\u00a0step-off 14-12, and swing it from point 14.\"\"<\/li>\r\n \t
  6. Pick up line 12-11 from the TLD, and swing it from point 12.\"\"<\/li>\r\n \t
  7. Pick up step-off 11-13, and swing it from point 13.\"\"<\/li>\r\n \t
  8. Follow this same procedures, swing the true length of an\u00a0element line\u00a0and a\u00a0step-off to create the next point until you reach point 1.\"\"<\/li>\r\n \t
  9. Draw in the all the\u00a0element lines and outside edges, use a flexible curve for the round ends.\"\"<\/li>\r\n<\/ol>\r\nhttps:\/\/www.youtube.com\/watch?v=fTMPyRXjcyQ&list=PL0YcC46LnT8di2DsnBZrMgeEtso_LWIHL&index=14","rendered":"
      \n
    1. Draw a full plan view<\/a><\/strong> complete with all element lines<\/a> <\/strong>and labeling. Label one half of the plan view, go from large end to small end, zigzagging back and forth with the numbering 1-14. Remember, every round to round will be on centre one way, but it is always worth drawing the whole thing.\"\"<\/strong><\/li>\n
    2. Create a\u00a0TLD<\/a><\/strong>\u00a0and label all the\u00a0element lines.\"\"<\/strong><\/li>\n
    3. Draw a vertical line equal to the true length<\/a><\/strong> of line 13-14.\"\"<\/li>\n
    4. From the\u00a0TLD, pick up the true length of line 13-12 and swing it from point 13 back towards point 14. Remember to work both sides at the same time.\"\"<\/strong><\/li>\n
    5. Next, pick up\u00a0step-off 14-12, and swing it from point 14.\"\"<\/li>\n
    6. Pick up line 12-11 from the TLD, and swing it from point 12.\"\"<\/li>\n
    7. Pick up step-off 11-13, and swing it from point 13.\"\"<\/li>\n
    8. Follow this same procedures, swing the true length of an\u00a0element line\u00a0and a\u00a0step-off to create the next point until you reach point 1.\"\"<\/li>\n
    9. Draw in the all the\u00a0element lines and outside edges, use a flexible curve for the round ends.\"\"<\/li>\n<\/ol>\n