Electromotive Force

You can think of many different types of voltage sources. Batteries themselves come in many varieties. There are many types of mechanical/electrical generators, driven by many different energy sources, ranging from nuclear to wind. Solar cells create voltages directly from light, while thermoelectric devices create voltage from temperature differences.

A few voltage sources are shown in (Figure). All such devices create a potential difference and can supply current if connected to a resistance. On the small scale, the potential difference creates an electric field that exerts force on charges, causing current. We thus use the name electromotive force, abbreviated emf.

Emf is not a force at all; it is a special type of potential difference. To be precise, the electromotive force (emf) is the potential difference of a source when no current is flowing. Units of emf are volts.

Electromotive force is directly related to the source of potential difference, such as the particular combination of chemicals in a battery. However, emf differs from the voltage output of the device when current flows. The voltage across the terminals of a battery, for example, is less than the emf when the battery supplies current, and it declines further as the battery is depleted or loaded down. However, if the device’s output voltage can be measured without drawing current, then output voltage will equal emf (even for a very depleted battery).

Internal Resistance

As noted before, a 12-V truck battery is physically larger, contains more charge and energy, and can deliver a larger current than a 12-V motorcycle battery. Both are lead-acid batteries with identical emf, but, because of its size, the truck battery has a smaller internal resistance [latex]r[/latex]. Internal resistance is the inherent resistance to the flow of current within the source itself.

(Figure) is a schematic representation of the two fundamental parts of any voltage source. The emf (represented by a script E in the figure) and internal resistance [latex]r[/latex] are in series. The smaller the internal resistance for a given emf, the more current and the more power the source can supply.

The internal resistance [latex]r[/latex] can behave in complex ways. As noted, [latex]r[/latex] increases as a battery is depleted. But internal resistance may also depend on the magnitude and direction of the current through a voltage source, its temperature, and even its history. The internal resistance of rechargeable nickel-cadmium cells, for example, depends on how many times and how deeply they have been depleted.

Why are the chemicals able to produce a unique potential difference? Quantum mechanical descriptions of molecules, which take into account the types of atoms and numbers of electrons in them, are able to predict the energy states they can have and the energies of reactions between them.

In the case of a lead-acid battery, an energy of 2 eV is given to each electron sent to the anode. Voltage is defined as the electrical potential energy divided by charge: [latex]V=\frac{{P}_{\text{E}}}{q}[/latex]. An electron volt is the energy given to a single electron by a voltage of 1 V. So the voltage here is 2 V, since 2 eV is given to each electron. It is the energy produced in each molecular reaction that produces the voltage. A different reaction produces a different energy and, hence, a different voltage.

Terminal Voltage

The voltage output of a device is measured across its terminals and, thus, is called its terminal voltage[latex]\phantom{\rule{0.25em}{0ex}}V[/latex]. Terminal voltage is given by

where [latex]r[/latex] is the internal resistance and [latex]I[/latex] is the current flowing at the time of the measurement.

[latex]I[/latex] is positive if current flows away from the positive terminal, as shown in (Figure). You can see that the larger the current, the smaller the terminal voltage. And it is likewise true that the larger the internal resistance, the smaller the terminal voltage.

Suppose a load resistance [latex]{R}_{\text{load}}[/latex] is connected to a voltage source, as in (Figure). Since the resistances are in series, the total resistance in the circuit is [latex]{R}_{\text{load}}+r[/latex]. Thus the current is given by Ohm’s law to be

We see from this expression that the smaller the internal resistance [latex]r[/latex], the greater the current the voltage source supplies to its load [latex]{R}_{\text{load}}[/latex]. As batteries are depleted, [latex]r[/latex] increases. If [latex]r[/latex] becomes a significant fraction of the load resistance, then the current is significantly reduced, as the following example illustrates.

Battery testers, such as those in (Figure), use small load resistors to intentionally draw current to determine whether the terminal voltage drops below an acceptable level. They really test the internal resistance of the battery. If internal resistance is high, the battery is weak, as evidenced by its low terminal voltage.

Some batteries can be recharged by passing a current through them in the direction opposite to the current they supply to a resistance. This is done routinely in cars and batteries for small electrical appliances and electronic devices, and is represented pictorially in (Figure). The voltage output of the battery charger must be greater than the emf of the battery to reverse current through it. This will cause the terminal voltage of the battery to be greater than the emf, since [latex]V=\text{emf}-\text{Ir}[/latex], and [latex]I[/latex] is now negative.

Multiple Voltage Sources

There are two voltage sources when a battery charger is used. Voltage sources connected in series are relatively simple. When voltage sources are in series, their internal resistances add and their emfs add algebraically. (See (Figure).) Series connections of voltage sources are common—for example, in flashlights, toys, and other appliances. Usually, the cells are in series in order to produce a larger total emf.

But if the cells oppose one another, such as when one is put into an appliance backward, the total emf is less, since it is the algebraic sum of the individual emfs.

A battery is a multiple connection of voltaic cells, as shown in (Figure). The disadvantage of series connections of cells is that their internal resistances add. One of the authors once owned a 1957 MGA that had two 6-V batteries in series, rather than a single 12-V battery. This arrangement produced a large internal resistance that caused him many problems in starting the engine.

If the series connection of two voltage sources is made into a complete circuit with the emfs in opposition, then a current of magnitude [latex]I=\frac{\left({\text{emf}}_{1}–{\text{emf}}_{2}\right)}{{r}_{1}+\phantom{\rule{0.25em}{0ex}}{r}_{2}}[/latex] flows. See (Figure), for example, which shows a circuit exactly analogous to the battery charger discussed above. If two voltage sources in series with emfs in the same sense are connected to a load [latex]{R}_{\text{load}}[/latex], as in (Figure), then

[latex]I=\frac{\left({\text{emf}}_{1}+\phantom{\rule{0.25em}{0ex}}{\text{emf}}_{2}\right)}{{r}_{1}+\phantom{\rule{0.25em}{0ex}}{r}_{2}+{R}_{\text{load}}}[/latex] flows.

(Figure) shows two voltage sources with identical emfs in parallel and connected to a load resistance. In this simple case, the total emf is the same as the individual emfs. But the total internal resistance is reduced, since the internal resistances are in parallel. The parallel connection thus can produce a larger current.

Here, [latex]I=\frac{\text{emf}}{\left({r}_{\text{tot}}\phantom{\rule{0.25em}{0ex}}+\phantom{\rule{0.25em}{0ex}}{R}_{\text{load}}\right)}[/latex] flows through the load, and [latex]{r}_{\text{tot}}[/latex] is less than those of the individual batteries. For example, some diesel-powered cars use two 12-V batteries in parallel; they produce a total emf of 12 V but can deliver the larger current needed to start a diesel engine.

Animals as Electrical Detectors

A number of animals both produce and detect electrical signals. Fish, sharks, platypuses, and echidnas (spiny anteaters) all detect electric fields generated by nerve activity in prey. Electric eels produce their own emf through biological cells (electric organs) called electroplaques, which are arranged in both series and parallel as a set of batteries.

Electroplaques are flat, disk-like cells; those of the electric eel have a voltage of 0.15 V across each one. These cells are usually located toward the head or tail of the animal, although in the case of the electric eel, they are found along the entire body. The electroplaques in the South American eel are arranged in 140 rows, with each row stretching horizontally along the body and containing 5,000 electroplaques. This can yield an emf of approximately 600 V, and a current of 1 A—deadly.

The mechanism for detection of external electric fields is similar to that for producing nerve signals in the cell through depolarization and repolarization—the movement of ions across the cell membrane. Within the fish, weak electric fields in the water produce a current in a gel-filled canal that runs from the skin to sensing cells, producing a nerve signal. The Australian platypus, one of the very few mammals that lay eggs, can detect fields of 30 [latex]\frac{\text{mV}}{m}[/latex], while sharks have been found to be able to sense a field in their snouts as small as 100 [latex]\frac{\text{mV}}{m}[/latex] ((Figure)). Electric eels use their own electric fields produced by the electroplaques to stun their prey or enemies.

Solar Cell Arrays

Another example dealing with multiple voltage sources is that of combinations of solar cells—wired in both series and parallel combinations to yield a desired voltage and current. Photovoltaic generation (PV), the conversion of sunlight directly into electricity, is based upon the photoelectric effect, in which photons hitting the surface of a solar cell create an electric current in the cell.

Most solar cells are made from pure silicon—either as single-crystal silicon, or as a thin film of silicon deposited upon a glass or metal backing. Most single cells have a voltage output of about 0.5 V, while the current output is a function of the amount of sunlight upon the cell (the incident solar radiation—the insolation). Under bright noon sunlight, a current of about [latex]\text{100}\phantom{\rule{0.25em}{0ex}}{\text{mA/cm}}^{2}[/latex] of cell surface area is produced by typical single-crystal cells.

Individual solar cells are connected electrically in modules to meet electrical-energy needs. They can be wired together in series or in parallel—connected like the batteries discussed earlier. A solar-cell array or module usually consists of between 36 and 72 cells, with a power output of 50 W to 140 W.

The output of the solar cells is direct current. For most uses in a home, AC is required, so a device called an inverter must be used to convert the DC to AC. Any extra output can then be passed on to the outside electrical grid for sale to the utility.