8.1 Physical Weathering

Intrusive igneous rocks form at depths of 100s of metres to 10s of kilometres. Most metamorphic rocks are formed at depths of kilometres to 10s of kilometres. Sediments are turned into sedimentary rocks only when they’re buried by other sediments to depths in excess of several 100s of metres. Weathering can’t happen until these rocks are revealed at Earth’s surface by uplift and the erosion of overlying materials. Once the rock is exposed at the surface as an outcrop, weathering begins.

The agents of physical weathering can be broadly classified into two groups: those that cause the outer layers of a rock to expand, and those that act like wedges to force the rock apart.

Physical Weathering By Expansion

Some processes at Earth’s surface can cause a thin outer layer of a rock to expand. Deeper than the thin outer layer, the rock does not expand. The difference is accommodated by a crack developing between the outer and inner layers, breaking the outer layer off in slabs (Figures 8.2 and 8.3). When layers break off a rock in slabs or sheets, it is referred to as exfoliation. Granite tends to exfoliate parallel to the exposed surface because it doesn’t have pre-existing planes of weakness to determine how it breaks. In contrast, sedimentary rocks tend to exfoliate along the contacts between different sedimentary layers, and metamorphic rocks tend to exfoliate parallel to aligned minerals.

 

Figure 8.2 Close-up view of exfoliation of a granite dome in the Enchanted Rock State Natural Area, Texas, USA. Source: Wing-Chi Poon (2005), CC BY-SA 2.5. View source.
Figure 8.3 View of exfoliation at a distance (centre of image) in granite exposed on the west side of the Coquihalla Highway north of Hope, B.C. Source: Steven Earle (2015), CC BY 4.0. View source.

Why Do Rocks Expand?

A rock within the Earth has pressure exerted upon it by other rocks sitting above it. This is called confining pressure. When the overlying mass is removed by weathering, the confining pressure decreases, allowing the rock to expand. The cracking that results is sometimes called pressure-release cracking.

Heating a rock can also cause it to expand. If the rock is heated rapidly, as during a wildfire, cracks can form. If it goes through large daily temperature swings (e.g., in the desert where it’s very hot during the day but cold at night), cracking can also eventually result as the rock is weakened.

Physical Weathering by Wedging

In wedging, a pre-existing crack in a rock is made larger by forcing it open.

Frost Wedging

Frost wedging (or ice wedging) happens when water seeps into cracks, then expands upon freezing. The expansion enlarges the cracks (Figure 8.4). The effectiveness of frost wedging depends on how often freezing and thawing occur. Frost wedging won’t be as important in warm areas where freezing is infrequent, in very cold areas where thawing is infrequent, or in very dry areas, where there is little water to seep into cracks.

 

Figure 8.4 A rock broken by ice wedging sits in a stream in Mount Revelstoke National Park, Canada. Rocks break apart when ice expands in pre-existing cracks. Source: Karla Panchuk (2018) CC BY 4.0.

Frost wedging is most effective in climates where for at least part of the year, temperatures swing between warm and freezing. In many parts of Canada, the temperature swings between freezing at night and thawing in the day tens to hundreds of times a year. Even in warm coastal areas of southern British Columbia, freezing and thawing transitions are common at higher elevations. A common feature in areas where frost wedging is important is a talus slope. It’s a fan-shaped deposit of fragments that have been popped off of rocks above, and piled up on steep slopes below (Figure 8.5).

 

Figure 8.5 An area with very effective frost wedging near Keremeos, BC. The fragments that were wedged away from the cliffs above have accumulated in a talus deposit at the base of the slope. The rocks in this area are variable in colour, which is reflected in the colours of the talus. Source: Steven Earle (2015), CC BY 4.0. View source.

Salt Wedging

Salt wedging happens when saltwater seeps into rocks and then evaporates on a hot sunny day. Salt crystals grow within cracks and pores in the rock, and the growth of these crystals can push grains apart, causing the rock to weaken and break. There are many examples of this on the rocky shorelines of Vancouver Island and the Gulf Islands, where sandstone outcrops are common and salty seawater is readily available (Figure 8.6). The honeycomb structure of rounded holes, called tafoni, is related to the original roughness of the surface. Low spots collect salt water, causing the effect to be accentuated around existing holes.

 

Figure 8.6 Tafoni (Honeycomb weathering) in sandstone on Gabriola Island, British Columbia. The holes are caused by crystallization of salt within rock pores. Source: Steven Earle (2015), CC BY 4.0. View source.

Plant and Animal Activity

The effects of plants are significant in mechanical weathering. Roots can force their way into even the tiniest cracks. They exert tremendous pressure on the rocks as they grow, widening the cracks and breaking the rock. This is called root wedging (Figure 8.7).

 

Figure 8.7 Root wedging along a quarry wall. Left: Rocks beneath the thick red beds have been split into sheets by tree roots. Right: A closer examination reveals that tree roots are working into vertical cracks as well. Source: Karla Panchuk (2018), CC BY 4.0.

Animals can excavate and remove huge volumes of soil, and thus expose the rock to weathering by other mechanisms. Humans modify vast tracts of land by excavation, and have a profound effect on accelerating physical weathering.

 

Practice with Types of Physical Weathering

 

Now that you’re warmed up, try this:

 Erosion

Physical weathering is greatly facilitated by erosion.  Erosion is the removal of weathering products, such as fragments of rock. This exposes more rock to weathering, accelerating the process. A good example of weathering and erosion working together is the talus shown in Figure 8.5. The rock fragments forming the talus piles were broken off the steep rock faces at the top of the cliff by ice wedging, and then removed by gravity.

Gravity doesn’t always work alone to remove weathering products. Other agents of erosion include water in streams, ice in glaciers, and waves on coasts.

 

Concept Check

 

License

Icon for the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License

Physical Geology - H5P Edition V1.1 Copyright © 2021 by Karla Panchuk is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License, except where otherwise noted.